Menu
The oil refining processes produce large quantities of waste gases with sulfur content. The sulfur must be recovered in order to meet environmental legislation that limits total sulfur emissions from the plant
Our blowers are used in these Sulfur Recovery Units (SRU) to supply the necessary primary air to the fumace reactor.
The Continental Industrie blowers can comply with the API 617 Norm 7 th edition with some minor deviations..
More than 40 years of experience in research, development and manufacture of centrifugal machines with several thousand machines installed makes Continental Industrie blowers and exhausters the symbol of reliability for continuous duty and extremely rugged service, 24 hours a day, 7 days a week.
Multistage Centrifugal Compressors that Continental Industrie offers are mainly the simple design and high mechanical reliability, both highly appreciated qualities for this application. The characteristics of the air (variable flow rate with constant vacuum and drive shaft power proportional to the flow rate used) allow our machines operate with a stable flow no matter how many active operators there are. Therefore, the energy consumption is proportional to the number of inlet nozzles that are actually used. The operating characteristic therefore generates significant energy savings
The durability and reliability of our machines are important for this application.
In particular, for pneumatic conveying systems operating with vacuum, our cast machines that create the vacuum are less sensitive to the possible passage of particles through the machie, than other technologies.
The advantages of the cast iron or aluminium centrifugal multistage exhausters Continental Industrie manufactures are mainly the simple design and mechanical reliability, both highly important for this application.
The extremely simple design of our machines guarantees maximum reliabilit.
The function of the blower, for this application, is to supply to air one or several tanks in order to brin oxygen to bacteria which must degrade the organic matter. To inject this air, the blower must overcome the resistance, or backpressure due to the water height and diffuser/piping losses.
As the effluent quantity to be treated changes over the course of time, it is desirable to inject only the amount of oxygen necessary and in sufficient quantities to optimize the oxygen needs of the bacteria, thus making it imperative to have the ability to vary the flow while keeping a constant pressure.
The Centrifugal Multistage Technology allows variation of the flow by a simple regulation butterfly valve located at the inlet, and therefore energy consumption is in proportion to the actual flow point, therby optimizing performance and minimizing power consumption at all operating conditions.
The ovens with fluidizing beds are frequently used to incinerate waste products or sludge from wastewater treatment plants. The principle of combustion by bluidizing bed is to “heat” a sand bed and to put the sand particles in suspension by an air injection nozzle system. The combustible material is then fed into the bed where the high sand temperature ingnites the material, and the active movement of the fluidized sand particles, completes the incineration the combustible materials.
The Centrifugal Multistage Blower supplies air, which “fluidizes” the sand bed. This air is also used for the supply of necessary oxygen for the combustion of waste products. The operating curve of the blower covers a large flow range, thereby allowing a variable flow rate that can be adjusted to match the qualtity of waste products to incinerate. Our blowrs can also be used for the supply of air tor the burner used to heat the sand bed.
The handling of compressed gases must be considered more hazardous than the handling of liquid and solid. The procedures adopted for the safe handling of compressed gases are mainly centered on containment of the material, to prevent its escape to the atmosphere, and proper control of pressure and flow.
The handling of compressed gases must be considered more hazardous than the handling of liquid and solid. The procedures adopted for the safe handling of compressed gases are mainly centered on containment of the material, to prevent its escape to the atmosphere, and proper control of pressure and flow.
The features of the centrifugal multi-stage blowers manufactured by Continental Industrie, are mainly the simple design and mechanical reliability, both highly appreciated for this application.
Steam is the gas formed when water passes from the liquid to the gaseous state. At the molecular level, this is when H2O molecules manage to break free from the bonds keeping them together.
Our blowers are used for these vacuum cleaners ironing facilities, these vacuum cleaners are used to create a vacuum network that connects to the presses used to create a vacuum in the presses, remove humidity and dry the clothes ironed for optimal finish.
In function of the number of presses, you select a vacuum that gives enough flow to create the vacuum necessary and maintain a regular vacuum entire line of presses.
Carbon black is produced from a petroleum oil based substance. The petroleum substance is fed into a specially adapted combustion chamber and heated to about 950ºC. This process “cracks” the petroleum to form a gas and carbon black powder.
Those elements go through various filters, which extract the carbon black powder. This powder with added water creates larger granules. Those granules are processed dried and conditioned. This carbon black powder is used in a wide variety of products, including the manufacturing of pneumatic tires and printing links.
Our Blowers are used to supply air to the combustion chamber burners. The blowers characteristic, in terms of simplicity and mechanical reliability and the performance curve make our equipments a perfect fit for this process.
Intermingling fibbers carry out the manufacturing of non-woven “tissue” under a water spray system.
Before drying this tissue in ovens, it is necessary to extract a maximum of water, in order to reduce the power consumed by the oven. Our centrifugal exahusters are used for this liquid extraction.
This extraction is accomplished by pulling air through the tissue at a high velocity. By mechanically extracting most of the water from the tissue, you can greatly reduce the energy requirements of the more expensive heated drying process.
It also allows you to increase the production efficiency. The quality, durability and high efficiency of our product makes liquid extraction an excellent centrifugal blower application.
Category for all kind of combustion air, no gas Combustion or burning is the sequence of exothermic chemical reactions between a fuel and an oxidant accompanied by the production of heat and conversion of chemical species
The Multistage Centrifugal Technology offers a high bolume of air at a high pressure to provide forced air through the combustion process.
The operating curve of the blower covers a large flow range, thereby allowing a variable flow rate that can be adjusted to match the quantity of waste products to incinerate. Our blowers can also be used for the supply of air for the burner used to heat the sand bed.
Salt water is desalinated to produce fresh water suitable for human consumption or irrigation. The traditional process used in these opration is vacuum distillation essentially the boiling of water at less than atmospheric pressure and thus a much lower temperature than normal.
This is because the boiling of aliquid occurs when the vapor pressure equals the ambient pressure and vapor pressure increases with temperature. Thus, because of the reduced temperature, energy is saved. Multistage flash distillation, a leading method, accounted for 85% worlwide of production.
The principal competing processes use membranes to desalinate, principally applying reverse osmosis technology. Membrane processes use semipermeable membranes and pressure to separate salts from water.
Sport samples are taken at one time at one point, normally via a pilot tube inserted in the process or pipeline. The sample is collected in a sample cylinder and takent to a laboratory for analysis.
Continuous samples are taken from the line and fed into an alalyser that continuosly analyses the gas. Alternatively, representative samples of gas are collected using a by-pass sampler mounted adjacent to the pipe or mounted directly on the pipe. Grab samples are then collected in a sample cylinder over a period, for later analysis in a laboratory.
The features of the centrifugal multi-stage blowers manufactured by Continental Industrie, are mainly the simple design and mechanical reliability, both highly appreciated for this application.
Our multi-stage blowers are used for the vacuum removal of biogas from the extraction zone of the biogas to the combustion system (Burner, thermal motor, etc.)
The Continental Industrie centrifugal blowers are also used for the landfill gas extraction by vacuum of volatlle organic compounds (VOC´s) through pumping wells.
The durability of the centrifugal blowers, their specific sealing system “biogas type”, and their performance characteristics, are all well suited to these applications requiring operation over a wide volumetric flow range.
Group 2 material: category 2 G according to the Atex 94/9/CE directive, usable in zone 1 or zone 2.
Group 2 material: category 3 G according to the Atex 94/9/CE directive, usable in zone 2.
An air knife is a tool used to blow off liquid or debris from produtcs as they on conveyors. Air knives are normally used in manufacturing or as the first step in a recursive recycling process to separate lighter or smaller particles from other components for use in later or subsequent steps, post manufacturing parts drying and conveyor cleaning, part of component cleaning.
The knife consists of a high intensity, uniform sheet of laminar airflow sometimes known as streamline flow. An industrial air knife is a pressurized air plenum containing a series of holes or continuous slots through which pressurized air exits in a laminar flow pattern. The exit air velocity then creates an impact air velocity onto the surface of whatever object the air is directed.
In mining the flotation is a process for separating minerals from gangue, the waste rock, by taking advantage of differences in their hydrophobic. Differences between valuable minerals and waste gangue are increased through the use of surfactants and wetting agents in the flotation cell which are designed to be forced air fed and require a flotation air blower.
Crude ore is ground to a fine powder and mixed with water, frothing reagents, and collecting reagents. When air is blown through the mixture, mineral particles cling to the bubbles, which rise to form froth on the surface. The waste material (gangue) settles to the blottom. The froth is skimmed off, and the water and chemicals are distilled or oterwise removed, leaving a clean concentrate. The process, also called the froth-flotation process, is used for a number of minerals, especially silver
To protect iron sheets from corrosion, manufacturers apply a galvanized coating to the sheets. For this, the iron sheet goes through a liquid galvanizing bath and re-emerges with a coating of non-uniform thickness.
To leave only the necessary and sufficient thickness to protect the iron sheet, it is necessary to take off the excess by the way of an air knife. The centrifugal blowers is used to supply in air those air knife nozzles.
To obtain a good quality of coating, it is imperative to supply an oil free, non-polluted air stream, constant and without pulsation. One of the characteristics of the Centrifugal Multistage Blower design is to supply oil free, clean air and without pulsation.
Therefore our blowrers are preferred for this application.